.\" Copyright (c) 2004
.\"	Bill Paul <wpaul@windriver.com>. All rights reserved.
.\"
.\" Redistribution and use in source and binary forms, with or without
.\" modification, are permitted provided that the following conditions
.\" are met:
.\" 1. Redistributions of source code must retain the above copyright
.\"    notice, this list of conditions and the following disclaimer.
.\" 2. Redistributions in binary form must reproduce the above copyright
.\"    notice, this list of conditions and the following disclaimer in the
.\"    documentation and/or other materials provided with the distribution.
.\" 3. All advertising materials mentioning features or use of this software
.\"    must display the following acknowledgement:
.\"	This product includes software developed by Bill Paul.
.\" 4. Neither the name of the author nor the names of any co-contributors
.\"    may be used to endorse or promote products derived from this software
.\"   without specific prior written permission.
.\"
.\" THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
.\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
.\" ARE DISCLAIMED.  IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
.\" BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
.\" CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
.\" SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
.\" INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
.\" CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
.\" ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
.\" THE POSSIBILITY OF SUCH DAMAGE.
.\"
.\" $FreeBSD: release/10.0.0/share/man/man4/vge.4 235319 2012-05-12 03:46:43Z gjb $
.\"
.Dd May 29, 2011
.Dt VGE 4
.Os
.Sh NAME
.Nm vge
.Nd "VIA Networking Technologies Velocity Gigabit Ethernet adapter driver"
.Sh SYNOPSIS
To compile this driver into the kernel,
place the following lines in your
kernel configuration file:
.Bd -ragged -offset indent
.Cd "device miibus"
.Cd "device vge"
.Ed
.Pp
Alternatively, to load the driver as a
module at boot time, place the following line in
.Xr loader.conf 5 :
.Bd -literal -offset indent
if_vge_load="YES"
.Ed
.Sh DESCRIPTION
The
.Nm
driver provides support for various NICs and embedded Ethernet interfaces
based on the VIA Technologies VT6120, VT6122, VT6130 and VT6132 Velocity
Family Gigabit Ethernet controller chips.
.Pp
The VT6120/VT6122 is a 33/66MHz 64-bit PCI device which combines a tri-speed
MAC with an integrated 10/100/1000 copper PHY.
(Some older cards use an external PHY.)
The VT6130/VT6132 is the PCI express version of Velocity family.
The MAC supports TCP/IP hardware
checksums (IPv4 only), TCP large send, VLAN tag insertion and stripping,
as well as VLAN filtering, a 64-entry CAM filter and a 64-entry VLAN filter,
64-bit multicast hash filter, 4 separate transmit DMA queues, flow control
and jumbo frames (not on VT6130/VT6132) up to 16K in size.
The Velocity family controllers have a 16K receive FIFO and 48K transmit FIFO.
.Pp
The
.Nm
driver takes advantage of the controller's checksum offload and VLAN
tagging features, as well as the jumbo frame (except VT6130/VT6132) and CAM
filter support.
The CAM filter is used for multicast address filtering to provide
64 perfect multicast address filter support.
If it is necessary for the interface to join more than 64 multicast
groups, the driver will switch over to using the hash filter.
.Pp
The jumbo frame support can be enabled by setting the interface MTU
to any value larger than the default of 1500 bytes, up to a maximum
of 9000 bytes.
Jumbo frames are disabled on the VT6130/VT6132 controllers because the TX
MAC will hang when trying to send a frame that is larger than 4K.
The receive and transmit checksum offload support
can be toggled on and off using the
.Xr ifconfig 8
utility.
.Pp
The
.Nm
driver supports the following media types:
.Bl -tag -width ".Cm 10baseT/UTP"
.It Cm autoselect
Enable autoselection of the media type and options.
The user can manually override
the autoselected mode by adding media options to
.Xr rc.conf 5 .
.It Cm 10baseT/UTP
Set 10Mbps operation.
The
.Xr ifconfig 8
.Cm mediaopt
option can also be used to select either
.Cm full-duplex
or
.Cm half-duplex
modes.
.It Cm 100baseTX
Set 100Mbps (Fast Ethernet) operation.
The
.Xr ifconfig 8
.Cm mediaopt
option can also be used to select either
.Cm full-duplex
or
.Cm half-duplex
modes.
.It Cm 1000baseTX
Set 1000baseTX operation over twisted pair.
The
.Xr ifconfig 8
.Cm mediaopt
option can also be used to select either
.Cm full-duplex
or
.Cm half-duplex
modes.
.El
.Pp
The
.Nm
driver supports the following media options:
.Bl -tag -width ".Cm full-duplex"
.It Cm full-duplex
Force full duplex operation.
.It Cm half-duplex
Force half duplex operation.
.El
.Pp
For more information on configuring this device, see
.Xr ifconfig 8 .
.Sh HARDWARE
The
.Nm
driver supports VIA Networking VT6120, VT6122, VT6130 and VT6132 based
Gigabit Ethernet adapters including:
.Pp
.Bl -bullet -compact
.It
VIA Networking LAN-on-motherboard Gigabit Ethernet
.It
ZyXEL GN650-T 64-bit PCI Gigabit Ethernet NIC (ZX1701)
.It
ZyXEL GN670-T 32-bit PCI Gigabit Ethernet NIC (ZX1702)
.El
.Sh LOADER TUNABLES
Tunables can be set at the
.Xr loader 8
prompt before booting the kernel or stored in
.Xr loader.conf 5 .
.Bl -tag -width "xxxxxx"
.It Va hw.vge.msi_disable
This tunable disables MSI support on the Ethernet hardware.
The default value is 0.
.El
.Sh SYSCTL VARIABLES
The following variables are available as both
.Xr sysctl 8
variables and
.Xr loader 8
tunables:
.Bl -tag -width "xxxxxx"
.It Va dev.vge.%d.int_holdoff
Maximum number of time to delay interrupts.
The valid range is 0 to 5100 in units of 1us, the default is
150 (150us).
The resolution of timer is about 20us so finer tuning than
20us wouldn't be available.
The interface should be brought down and up again before a change
takes effect.
.It Va dev.vge.%d.rx_coal_pkt
Maximum number of packets to fire Rx completion interrupt.
The valid range is 1 to 255, the default is 64.
.It Va dev.vge.%d.tx_coal_pkt
Maximum number of packets to fire Tx completion interrupt.
The valid range is 1 to 255, the default is 128.
.El
.Sh DIAGNOSTICS
.Bl -diag
.It "vge%d: couldn't map memory"
A fatal initialization error has occurred.
.It "vge%d: couldn't map ports"
A fatal initialization error has occurred.
.It "vge%d: couldn't map interrupt"
A fatal initialization error has occurred.
.It "vge%d: failed to enable memory mapping!"
The driver failed to initialize PCI shared memory mapping.
This might
happen if the card is not in a bus-master slot.
.It "vge%d: watchdog timeout"
The device has stopped responding to the network, or there is a problem with
the network connection (cable).
.El
.Sh SEE ALSO
.Xr altq 4 ,
.Xr arp 4 ,
.Xr miibus 4 ,
.Xr netintro 4 ,
.Xr ng_ether 4 ,
.Xr polling 4 ,
.Xr vlan 4 ,
.Xr ifconfig 8
.Sh HISTORY
The
.Nm
device driver first appeared in
.Fx 5.3 .
.Sh AUTHORS
The
.Nm
driver was written by
.An Bill Paul Aq wpaul@windriver.com .
